ハードウエア メモ: ファイルサーバ

CPU:      Pentium 100 (downgraded to 80 ?)
memory:   48 M
IDE:      on board
Network:  Intel 100S
          Realtek Semiconductor 8139 10/100 Ethernet
serial:   ns16550a
DISK:     QUANTUM FIREBALL1080A
          IBM-DPTA-373420
          ST380021A

cpu0: Intel Pentium (P54C) (586-class), 80.99 MHz
total memory = 48768 KB
avail memory = 43148 KB
using 635 buffers containing 2540 KB of memory
RTC BIOS diagnostic error 20<config_unit>
BIOS32 rev. 0 found at 0xf0210
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Acer Labs M1451 Host-PCI Bridge (rev. 0xbd)
Acer Labs M1449 PCI-ISA Bridge (miscellaneous prehistoric, revision 0xc0) at pci0 dev 2 function 0 not configured
pciide0 at pci0 dev 3 function 0: CMD Technology PCI0640 (rev. 0x02)
pciide0: hardware does not support DMA
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALL1080A>
wd0: drive supports 8-sector pio transfers, lba addressing
wd0: 1039 MB, 2112 cyl, 16 head, 63 sec, 512 bytes/sect x 2128896 sectors
wd0: drive supports PIO mode 4, DMA mode 2
wd1 at pciide0 channel 0 drive 1: <IBM-DPTA-373420>
wd1: drive supports 16-sector pio transfers, lba addressing
wd1: 32253 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 66055248 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4
pciide0: primary channel interrupting at irq 14
pciide0: secondary channel wired to compatibility mode
wd2 at pciide0 channel 1 drive 0: <ST380021A>
wd2: drive supports 16-sector pio transfers, lba addressing
wd2: 76319 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5
pciide0: secondary channel interrupting at irq 15
vga1 at pci0 dev 4 function 0: Cirrus Logic CL-GD5434-8 (rev. 0xf9)
wsdisplay0 at vga1
Realtek Semiconductor 8139 10/100 Ethernet (ethernet network, revision 0x10) at pci0 dev 14 function 0 not configured
fxp0 at pci0 dev 15 function 0: i82550 Ethernet, rev 12
fxp0: interrupting at irq 5
fxp0: WARNING: Disabling dynamic standby mode in EEPROM to work around a
fxp0: WARNING: hardware bug.  You must reset the system before using this
fxp0: WARNING: interface.
fxp0: new EEPROM ID: 0x50a0
fxp0: EEPROM checksum @ 0x3f: 0xa535 -> 0xa537
fxp0: Ethernet address 00:02:b3:e8:b4:af
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at mainbus0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo